Efficient removal of Cr(VI) by a 3D Z-scheme TiO2-ZnxCd1-xS graphene aerogel via synergy of adsorption and photocatalysis under visible light

Efficient and robust photocatalysts for environmental pollutants removal with outstanding stability have great significance. Herein, we report a kind of three dimensional (3D) photocatalyst presented as Z-scheme heterojunction, which combining TiO 2 and Zn x Cd 1- x S with graphene aerogel to contrast TiO 2 -Zn x Cd 1- x S graphene aerogel (TSGA, x = 0.5) through a moderate hydrothermal process. The as-prepared Z-scheme TSGA was used to remove aqueous Cr(VI) via a synergistic effect of adsorption and visible light photocatalysis. The adsorption equilibrium can be reached about 40 min, then after about 30 min irradiation under visible light (wavelength ( λ) > 420 nm) the removal rate of Cr(VI) almost reached 100%, which is much better than the performance of pristine TiO 2 and Zn 0.5 Cd 0.5 S, as well as TiO 2 graphene aerogel (TGA) and Zn 0.5 Cd 0.5 S graphene aerogel (SGA). The virulent Cr(VI) was reduced to Cr(III) with hypotoxicity after photocatalysis on TSGA, meanwhile the as-synthesized TSGA presented a good stability and reusability. The reduced graphene oxide (rGO) sheets between TiO 2 and Zn 0.5 Cd 0.5 S played a role as charge transfer mediator, promoting the photoinduced electrons transfer and photocatalysis ability of TSGA was enhanced significantly. Hence,such photocatalyst exhibits a potential application on removing heavy metals with high efficiency and stability from polluted aqueous environment.     

钙钛矿型催化剂催化湿式氧化处理煤气化废水纳滤浓缩液

采用溶胶-凝胶法制备了Mn掺杂钙钛矿型催化剂LaFexMn1-xO3，并以其为催化剂催化湿式双氧水氧化处理煤气化废水纳滤浓缩液。采用XRD，SEM，FTIR技术对催化剂进行了表征。表征结果显示：制备的催化剂均具有标准的钙钛矿型结构，其中，LaFe0.9Mn0.1O3的结构稳定，比表面积大。实验结果表明：制备的催化剂中LaFe0.9Mn0.1O3的催化活性最高，且稳定性好，连续使用5次后催化活性未见明显减弱；在H2O2投加量3.0 g/L、n（H2O2）∶n（LaFe0.9Mn0.1O3）=12∶1、反应温度160 ℃、反应压力1 MPa、浓缩液pH 3、反应时间60 min的最优条件下，COD、UV254和TOC的去除率分别达到80.9%、95.2%和68.0%，BOD5/COD由0.02提升至0.40，可生化性大幅提高。     

Packed in-tube solid phase microextraction with graphene oxide supported on aminopropyl silica: Determination of target triazines in water samples

On-line in-tube solid phase microextraction (in-tube SPME) coupled to high performance liquid chromatography and tandem mass spectrometry (HPLC-MS/MS) was successfully applied to the determination of selected triazines in water samples. The method based on the employment of a packed column containing graphene oxide (GO) supported on aminopropyl silica (Si) showed that the extraction phase has a high potential for triazines extraction aiming to its physical-chemical properties including ultrahigh specific surface area, good mechanical and thermal stability and high fracture strength. Injection volume and loading time were both investigated and optimized. The method validation using Si-GO to extract and concentrate the analytes showed satisfactory results, good sensitivity, good linearity (0.2–4.0 µg L^?1) and low detection limits (1.1–2.9 ng L^?1). The high extraction efficiency was determined with enrichment factors ranging from 1.2–2.9 for the lowest level, 1.3–4.9 intermediate level and 1.2–3.0 highest level (n = 3). Although the analytes were not detected in the real samples evaluated, the method has demonstrated to be efficient through its application in the analysis of spiked triazines in ground and mineral water samples.     

纳米铁氧化物吸附处理重金属废水的研究进展

概述了用于吸附重金属的主要纳米铁氧化物的种类及其吸附效果,介绍了常见的纳米铁氧化物制备方法及改性方法,讨论了影响纳米铁氧化物吸附重金属的主要因素,并对纳米铁氧化物在水环境保护领域中的研究方向提出了展望:如发展绿色、高效的纳米铁氧化物制备工艺,探讨纳米铁氧化物结构调控和表面功能化对其吸附性能的影响等。     

300MW锅炉低NOx燃烧系统改造效果分析

针对日益严重的环境污染、锅炉热效率低等问题，阐述了燃煤锅炉炉内空间分级燃烧技术、煤粉浓淡高效分离技术改造项目和特点，提出了对燃烧器系统、一次风管道、二次风系统和空预器系统等系统进行具体的低氮改造措施。分析了300 MW燃煤锅炉低氮改造后的热经济性和安全性。经试验验证，1号锅炉低氮改造后，锅炉NOx 排放量大幅减少，排放浓度降到了280 mg／m3。     

In situ formation of bimetallic FeNi nanoparticles on sand through green technology: Application for tetracycline removal

• In situ preparation of FeNi nanoparticles on the sand via green synthesis approach. • Removal of tetracycline using GS-FeNi in batch and column study. • Both reductive degradation and sorption played crucial role the process. • Reusability of GS-FeNi showed about 77.39±4.3% removal on 4th cycle. • TC by-products after interaction showed less toxic as compared with TC. In this study, FeNi nanoparticles were green synthesized using Punica granatum (pomegranate) peel extract, and these nanoparticles were also formed in situ over quartz sand (GS-FeNi) for removal of tetracycline (TC). Under the optimized operating conditions, (GS-FeNi concentration: 1.5% w/v; concentration of TC: 20 mg/L; interaction period: 180 min), 99±0.2% TC removal was achieved in the batch reactor. The removal capacity was 181±1 mg/g. A detailed characterization of the sorbent and the solution before and after the interaction revealed that the removal mechanism(s) involved both the sorption and degradation of TC. The reusability of reactant was assessed for four cycles of operation, and 77±4% of TC removal was obtained in the cycle. To judge the environmental sustainability of the process, residual toxicity assay of the interacted TC solution was performed with indicator bacteria (Bacillus and Pseudomonas) and algae (Chlorella sp.), which confirmed a substantial decrease in the toxicity. The continuous column studies were undertaken in the packed bed reactors using GS-FeNi. Employing the optimized conditions, quite high removal efficiency (978±5 mg/g) was obtained in the columns. The application of GS-FeNi for antibiotic removal was further evaluated in lake water, tap water, and ground water spiked with TC, and the removal capacity achieved was found to be 781±5, 712±5, and 687±3 mg/g, respectively. This work can pave the way for treatment of antibiotics and other pollutants in the reactors using novel green composites prepared from fruit wastes.     

Biogenic palladium prepared by activated sludge microbes for the hexavalent chromium catalytic reduction: Impact of relative biomass

• Pd nanoparticles could be reduced and supported by activated sludge microbes. • The effect of biomass on Pd adsorption by microbes is greater than Pd reduction. • More biomass reduces Pd particle size, which is more dispersed on the cell surface. • When the biomass/Pd add to 6, the catalytic reduction rate of Cr(VI) reaches stable. Palladium, a kind of platinum group metal, owns catalytic capacity for a variety of hydrogenations. In this study, Pd nanoparticles (PdNPs) were generated through enzymatic recovery by microbes of activated sludge at various biomass/Pd, and further used for the Cr(VI) reduction. The results show that biomass had a strong adsorption capacity for Pd(II), which was 17.25 mg Pd/g sludge. The XRD and TEM-EDX results confirmed the existence of PdNPs associated with microbes (bio-Pd). The increase of biomass had little effect on the reduction rate of Pd(II), but it could cause decreasing particle size and shifting location of Pd(0) with the better dispersion degree on the cell surface. In the Cr(VI) reduction experiments, Cr(VI) was first adsorbed on bio-Pd with hydrogen and then reduced using active hydrogen as electron donor. Biomass improved the catalytic activity of PdNPs. When the biomass/Pd (w/w) ratio increased to six or higher, Cr(VI) reduction achieved maximum rate that 50 mg/L of Cr(VI) could be rapidly reduced in one minute.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

需求视角的中国能源消费氮氧化物排放研究

基于经济投入产出生命周期评价(EIO-LCA)模型构建了中国1990—2010年能源消费氮氧化物完全排放矩阵,从需求的角度分析了氮氧化物排放在部门和不同需求间的分布结构,并通过情景模拟深入探讨了最终需求结构变化对氮氧化物排放的综合影响和拉动效应,以期探索中国氮氧化物减排的多元化途径.研究结果显示,1990—2010年中国氮氧化物排放总量从878万t上升到2398万t,历年来由工业部门拉动产生的氮氧化物占总量的比重高达70%左右;由最终消费拉动的氮氧化物排放比重逐年下降,资本形成和出口拉动的氮氧化物排放比重逐年上升.氮氧化物排放强度则从47.0 kg·万元-1降至6.0 kg·万元-1,其中,能源和交通部门的排放强度最高.通过情景模拟可以看出,提高最终消费比重,扩大内需有利于氮氧化物总量减排,尤其是对工业部门的减排效果显著.实现氮氧化物总量减排目标,要求在技术进步之外,积极寻求多元减排措施,以强化减排效果,突出能源和交通等重点部门的氮氧化物防治体系建设,并通过扩大内需优化最终需求结构以促进工业部门氮氧化物减排.     

两种新型涂铁改性砂的过滤性能及反冲洗条件研究

以两种新型涂铁改性石英砂(纳米氧化铁改性砂,Nano-OCS;氧化铁改性砂,IOCS)及普通石英砂(RQS)为研究对象,考察了两种新型改性砂对沉后水腐殖酸及浊度的直接过滤效果,对其反冲洗条件进行优化研究,并对3种滤料的过滤效果进行了比较.结果表明,1滤层厚度为45 cm时,最佳滤速为6 m·h-1;3种滤料对腐殖酸和浊度的直接过滤效果依次为:Nano-OCSIOCSRQS,其中两种涂铁砂对腐殖酸的去除率分别为71.70%和61.61%;2Nano-OCS和IOCS滤柱的反冲洗流程分4步,对应的流程及最佳操作条件为:首先,用0.5 mol·L-1NaOH的溶液浸泡,气冲强度13 L·s-1·m-2,气冲时间6 min;然后,用0.075 mol·L-1的NaOH溶液与空气同时反冲洗,NaOH溶液冲洗强度为8 L·s-1·m-2,气冲强度13 L·s-1·m-2,冲洗时间3 min;接着用0.015 mol·L-1的FeCl3溶液与空气同时反冲洗,FeCl3溶液冲洗强度为8 L·s-1·m-2,气冲强度13L·s-1·m-2,冲洗时间2 min;最后,用清水冲洗,冲洗强度8 L·s-1·m-2,冲洗时间4 min.两种涂铁砂反冲洗前后表面形态结构更加复杂、粗糙度增加,对腐殖酸去除率进一步提高.3当滤层厚度由45 cm增加到80 cm时,Nano-OCS对腐殖酸直接过滤的最高去除率由74.6%提高至80.3%,平均去除率由57.9%提高至68.5%.